Bay Networks 4000 Guida di Installazione Scaricare il pdf (Pagina 25)

1-3Remote Annex 4000 Hardware Installation Guide

Chapter 1 Introduction

Terminal, Printer, and Communications Access

The Remote Annex 4000 provides terminal, printer, and

communications access to users on a local area network.

Figure 1-3 shows how the Remote Annex 4000 is used as a terminal

and communications server.

Figure 1-3. Remote Annex 4000 as a Terminal, Printer, and Communications Server

DEC

Remote

Terminal

Laser

Printer

Remote

Annex 4000

Plotter

Personal

Computer

IBM UNIX

Ethernet

Corporate LAN

1 2 ... 20 21 22 23 24 25 26 27 28 29 30 ... 161 162

Remote Annex 1
Revision Level History 3
Contents 5
Contents 6
Figures 10
Tables 12
About this Guide 13
Printing Conventions 14
Related Documents 15
Bay Networks Customer Service 17
World Wide Web 19
Customer Service FTP 20
Support Source CD 20
CompuServe 20
InfoFACTS 21
How to Get Help 22
Remote Network Access 23
Dial-up Routing 24
Chapter 1 Introduction 25
Remote Annex 4000 Description 26
Main Logic Board 26
Serial Line Controllers 27
Asynchronous SLC 28
Firmware and Software 29
Supported 30
Conﬁgurations 30
Watchdog Timer 30
Front Panel 31
Front Panel Components 32
Rear Panel 33
Rear Panel Components 34
Mode Jumper 35
Network Interface 35
Connectors 35
Physical Characteristics 36
6 in. (15 cm) 38
Before you Begin 39
Ethernet cable 41
Ethernet cable (see 42
Figure 2-3): 42
Figure 2-4): 43
Connecting a Console Terminal 45
Cable Retainer 48
PBX End 48
PBX Screw 49
Cable Retainer Screw 49
50–19,200 250 75 51
38,400 200 60 51
57,600 100 30 51
115,200 50 15 51
Connecting a Parallel Printer 52
Power Select Switch 53
2 Apply power 54
4000 to your LAN 57
This section describes: 57
Server. Proceed as follows: 58
Remote Annex and press 59
Prerequisites 61
The system responds: 64
For example: 65
For example: 65
Auto-initializing the ROMs 66
BOOTP response with the sm 68
4 Boot the Annex 69
Invoking the Console Monitor 70
Command Descriptions 74
Command Description Use 76
(Flash) is installed 83
Remote Annex 4000 is booted 86
4000 ROM Monitor commands 89
Network test – PASSED 94
[data bytes] [npackets] 97
Interface sequence: sl2,net 102
Prompt Description 104
Statistic Description 105
Power-up and Boot Procedures 108
On continuously 109
Flashing irregularly 109
Test Mode Diagnostics 113
Table 4-4 115
Boot Failures 117
Boot Error Report 118
Error Description 119
# /etc/erpcd –D5 123
# boot -v 123
Another Remote Annex 4000 124
VAX VMS Load Host on the LAN 125
● ● ● ● ● 126
Console Port 129
Coaxial Center 130
Conductor 130
Coaxial Shield 130
10Base5 Ethernet Port 131
10BaseT Ethernet Port 132
Serial Port 133
Pin Signal Pin Signal 134
Parallel Printer Port 135
Serial Port Cables 137
Remote Annex 4000 Champs 138
(continued on next page) 139
Serial Cable Wiring Diagrams 143
Printer Cables 145
Dataproducts 146
Printer Cable 146
Loopback Connectors 147
PBX Loopback 148
Connector 148
Contents of the Kit 149
Dress Panel Cover 150
(10 Places) 151
(4 Places) 152
Figure C-6) 153
Assembly Instructions 155
Power-up and Test 156
Test Button 157
PBX Loopback Plug 158
Numerics 159
Index 160

Commenti su questo manuale

Nessun commento

Bay Networks 4000 Guida di Installazione Pagina 25

Commenti su questo manuale

Prodotti e manuali riguardandi Software Bay Networks 4000